Boltsveiseapparat - 1600 J - 72000 µF
12835,00 NOK Inkl. mva, avgifter og fraktkostnader*

Boltsveiseapparat - 1600 J - 72000 µF

Leverandør: Stamos Germany | Artikkelnummer EX10020158 | Modell: S-STUD1600

Boltsveiseapparat - 1600 J - 72000 µF
Boltsveiseapparat - 1600 J - 72000 µF
Boltsveiseapparat - 1600 J - 72000 µF
Boltsveiseapparat - 1600 J - 72000 µF
Boltsveiseapparat - 1600 J - 72000 µF
Boltsveiseapparat - 1600 J - 72000 µF
Boltsveiseapparat - 1600 J - 72000 µF
360° foto
Klikk for å se bildene
12835,00 NOK
eller

587,74 NOK /måned /mo with Klarna

Lær mer

Inkl. mva, avgifter og fraktkostnader*

  • Gratis forsendelse til Norge

    ?

    Varen er på lager, leveringstid ca. 5-10 virkedager

  • 30 dagers returrett

    ?
  • 3 års garanti

Produkt-highlights

  • Energy storage 1,600 J
  • Capacity condenser 72,000 µF
  • Welding range M3 - M8
  • CD top ignition
  • for sheets from 0.5 mm

Egenskaper

  • A quick attachment of bolts, threads or rivets upon metal work pieces
  • High capacitor capacity of 72,000 μF
  • No preparatory work required
  • Welding range of M3 - M8
  • Pressure can be adjusted continuously
  • Modern LED display
  • Clear and easily readable display
  • Adjustable voltage regulator
  • Markings on the voltage regulator for different bolt sizes

Connections such as threads present a challenge in the metal processing, since they must be connected to the metal piece in such a way that they also withstand strong loads. With the S-STUD1600 stud welding tool from Stamos Germany, you can screw and fasten your screws, pins or cylinders in milliseconds to a wide range of metal parts.

The stud welder uses the CD ignition as the welding method. For this, the ignition tip of the bolt is placed on the workpiece; the current rises rapidly and causes the ignition tip to melt. For this, the ignition tip of the bolt is placed on the workpiece; the current rises rapidly and causes the ignition tip to melt. The arc is extinguished by light pressure, and the two parts are fixed together. The welding time is less than 3 MS.

Stud welding with pointed ignition is very well suited for thin plates from 0,5 mm upwards, but in principle the plate should be at least 1/10 of the bolt diameter. Therefore the welding method is very well suited in the electrical industry, laboratory technology, insulation technology, in housing / switch cabinet construction or in other areas where thin sheets are used as a workpiece.

The bolt welding machine S-STUD1600 requires no preparatory work such as drilling, tapping, punching or any other such prep work. It combines different metals and is suitable for most types of metal such as stainless steel, aluminium, copper and titanium. It can be used for sheet metals, housings, mounting covers and other metal work. The stud welder, with its high capacitor capacity of 72,000 μF and storage energy of 1,600 J, is also able weld hard metals.

The welding range of stud welding equipment is designed for threaded bolts or pins with sizes of M3 to M8 and a maximum length of 40 mm. For each size there is a separate chuck key (except M7) with which the bolt is securely fastened in the welding machine. No clamping rings flux or noble gases are needed for welding.

The pressure of the welding can be adjusted on the welding gun. Three cylinder pins on the head of the welding gun ensure a precise, vertical positioning of the bolt. The short welding time has excellent welding results, hardly any welding traces such as discolouration or deformation.

The adjustable voltage regulator has marks, which is used to set the optimum voltage for different bolt sizes between M3 and M8. Depending on the type of metal used, the voltage can be continuously increased or reduced according to your personal experience. Two earth cables improve the conductivity and increase the protection from a potential short-circuit.

The welding machine is easy to operate and has clear and simply display. In addition to the voltage regulator, there is a large, modern LED display, which displays the selected welding voltage. There are three status indicators for charging, operational and welding. For freedom of movement a 4 meters long cables for the pin welding gun is provided.

Model
S-STUD1600
Condition
New
Voltage
230 V
Frequency
50 Hz
Welding voltage
20 - 195 V
Rated input
500 kVA
Capacity condenser
72,000 µF
Energy storage
1,600 J
Welding range
M3 - M8
Welding efficiency
10-20 units/ min
Max. Bolt length
40 mm
Length bolt pistol with cable
4 m
Length of ground cable
3 m
Power cable
2,2 m
Dimensions (LxWxH)
56 x 21 x 38 cm
Weight
19 kg
Shipping dimensions (LxWxH)
65 x 32 x 43 cm
Shipping weight
26 kg
Teknisk tegning
Leveranseomfang
  • Stud welder
  • Stud welding gun with cable, 4 m
  • 2 x ground cable with clamp, 3 m
  • Clamping chuck, M3, M4, M5, M6, M8
  • Key for chucks

Vær den første til å skrive en produktanmeldelse



Gi anmeldelse
Anmeldelser kommer etter en godkjennelsesprosedyre på hjemmesiden

Die mit einem * markierten Felder sind Pflichtfelder.

Expondo-ekspert

Fortsatt usikker?

Våre eksperter står klar til å hjelpe.
21 93 53 21
Ma - Fr 10:00-16:00
Dette produktet
  • Energy storage 1,600 J
  • Capacity condenser 72,000 µF
  • Welding range M3 - M8
  • CD top ignition
  • for sheets from 0.5 mm

Varen er på lager, leveringstid ca. 5-10 virkedager

Boltsveiseapparat - 1600 J - 72000 µF

Boltsveiseapparat - 1600 J - 72000 µF

12835,00 NOK

Varen er på lager, leveringstid ca. 5-10 virkedager

  • Energy storage 1,600 J
  • Capacity condenser 72,000 µF
  • Welding range M3 - M8
  • CD top ignition
  • for sheets from 0.5 mm
  • Energy storage 2,500 J
  • Capacity condenser 108,000 ΜF
  • Welding range M3 - M10
  • CD top ignition
  • for sheets from 0.5 mm

Varen er på lager, leveringstid ca. 5-10 virkedager

Stud Welder - 2500 J - 108000 µF

Stud Welder - 2500 J - 108000 µF

(1)
16275,00 NOK

Varen er på lager, leveringstid ca. 5-10 virkedager

  • Energy storage 2,500 J
  • Capacity condenser 108,000 ΜF
  • Welding range M3 - M10
  • CD top ignition
  • for sheets from 0.5 mm