Plasmaskjærer - 60 A - 400 V

Artikkelnummer EX10020004 / Modell: S-Plasma 60P

Plasmaskjærer - 60 A - 400 V

  • Artikkelnummer EX10020004
  • Modell: S-Plasma 60P
  • I produktserien siden: 2008
 
 
 
6609,00 NOK

Inkl. mva, avgifter og fraktkostnader*

Betal inntil 24 avdrag av 302,64 NOK med Klarna

Lær mer

Varen er på lager, leveringstid ca. 5-8 virkedager

Plasma Cutter - 60 A - 400 V

The expert for craft supplies, Stamos Germany, offers first-class plasma cutters as well as welders. The Pro-range has been developed with inverter technology and is the best choice for maximum energy savings. In workshops, in agriculture and car repair shops, you need a cutting unit that is robust, flexible and reliable. The mobile plasma cutter S-Plasma 60P combines these features. Coated or rusted materials can be easily handled. All you need is a rotary current and pressurized air.

Attention! The device will be delivered without a high current connector!

Cut through steel as if it was butter - with the plasma cutter S-Plasma 60P from Stamos Germany

 

The plasma cutter is perfectly suited for precisely cutting stainless steel, cast iron, copper, brass and other electroconductive metals of up to 20 mm thickness. It generates a light arc with very high temperatures which allows you to cut through thick steel as if it were butter. The cutting current of the plasma cutter S-Plasma 60P is adjustable between 20 and 60 amps, which means that the device is adaptable to all conditions. First-class cutting quality, separation cuts and precision. Even at the more difficult end parts you get perfect cuts, thanks to the high reserve capacity. This high quality allows for better results with less reworks.

 

Saving time and working efficiently is becoming more and more important. Use your time in an effective manner - with the plasma cutter from Stamos Germany. The cutting speed is high, which ensures precise and high-quality weld seams with minimal material waste. The device has a jump-start-function which allows you to start it even during the gas post-flow.

Energy efficiency - Expensive plasma gas is a thing of the past

 

The device is powered by 400 volts. You can also use a generator with a minimum power output of 8 kVA for mobile operation. The plasma cutter is powered with inexpensive pressurized air. You need a compressor with a pressure of ingoing air of 6.2 bar and a passage of air of 170 l/m. This is best achieved with a 10-bar-compressor.

 

The construction stands out for its compact, robust design and its low tare weight of only 24.8 kg. The plasma cutter can be easily transported. The air-cooled cutting unit has a powder-coated sheet steel casing. The plasma cutter has an 8 m ground cable. You can work on a large scale without being hindered by a short cable.

Egenskaper

  • Exact current thanks to the seamless adjustment of the cutting current
  • High-powered ventilation for efficient cooling
  • Cost-effective with inexpensive pressurized air
  • Compact, mobile construction, versatile applications
  • Jump-start-function, even during the gas post-flow

Nøkkelord

Model
S-Plasma 60P
Condition
New
Input voltage
400 V, 3-phase
Input frequency
50 / 60 Hz
Rated input current
8,2 A
Input current, max.
11 A
Rated input power
5,3 kVA
Input power, max.
7,2 kVA
Open-circuit voltage
240 V
Cutting current
20 – 60 A
Duty cycle
60 %
Cutting current at 100% DC
46 A
Cutting current at 60 % DC
60 A
Ignition
Contact
Cutting power
22 mm
Kerf width
1 mm
Air flow
170 l/min
Air pressure
6 bar
Length, cable assembly
8 m
Length, ground cable
8 m
Length, power cord connection
1,2 m
Device cooling
Ventilator
Cooling distiller
Air
Power factor
0.93
Efficiency (below rated power)
≥ 0.85
Insulation class
F
Protection class
IP20S
Dimensions (LxWxH)
54 x 37 x 20 cm
Weight
24,8 kg
Shipping dimensions (LxWxH)
72 x 30 x 41 cm
Shipping weight
26,4 kg
 
MOSFET

The welder is equipped with a MOSFET transistor. This technology represents the highest standards of performance combined with compact and lightweight design. The result is 93% efficiency! The welding current is very stable and thus ensures a perfect weld.

 
VENTILATORS

Powerful fans ensure an optimal removal of heat from the unit.

 
GAS/AIR CONNECTION

For plasma cutting, a gas is required with which the molten metal is blown away from the work surface. Compressed air is a common solution for this. For this purpose, the plasma cutter has a compressor connection.

 
EARTHING SYSTEM

On the back of every welding machine is a screw with an earthing mark. Before use, earth the unit via a cross-section cable, which must be at least 6 mm².

 
GROUND TERMINAL CONNECTOR
 
CUTTING TORCH CONNECTION
 
SUPPLY VOLTAGE

This device works with a 3-phase connection (400 V +/- 10 %).

 
WELDING CURRENT
 
2-STROKE

Start the weld by placing pressure on the torch button. Stop the process by releasing the button.

 
PLASMA CUTTING

The plasma arc melts the metal and the kinetic energy of the compressed air blows the metal aside.

 
POWER SWITCH
 
DISPLAY

Shows the welding / cutting parameters.

 
OVERLOAD / FAULT LED

The LED light indicates overheating or a malfunction.

 
PRESSURE GAUGE (MANOMETER)

Shows the value of compressed air the compressor delivers to the plasma cutter. The plasma cutter has a pressure reducing valve which regulates the air pressure.

Med Stamos produkter kan du skille eller kombinere materialer effektivt og meget nøyaktig. Sortimentet inkluderer alt fra profesjonelle loddestasjoner, høyprofilerte sveiser og presise plasmaskjærer til passende tilbehør. La deg overbevises av funksjonaliteten, kvaliteten, allsidigheten – og ikke minst de gunstige priserne - hos våre profesjonelle produkter. Våre videoer viser våre populæreste produkter  i aksjon!

  • Plasma cutter S-Plasma 60P
  • Ground cable with clamp (8 m)
  • Cable assembly (8 m)
  • 2 electrodes
  • 2 ceramic nozzles
  • 2 cutting nozzles
  • 2 ceramic rings
  • Instruction manual

Vær den første til å skrive en produktanmeldelse



Gi anmeldelse
Anmeldelser kommer etter en godkjennelsesprosedyre på hjemmesiden

Die mit einem * markierten Felder sind Pflichtfelder.