B-varer Plasma Cutter - 90 A - 400 V - Pilot Ignition

Artikkelnummer EX20020129 / Modell: S-CUTTER 90

B-varer Plasma Cutter - 90 A - 400 V - Pilot Ignition

  • Artikkelnummer EX20020129
  • Modell: S-CUTTER 90
  • I produktserien siden: 2008
6539,00 NOK

Nettopris inkl. toll og frakt*

Betal inntil 24 avdrag av 299,43 NOK med Klarna

Lær mer

Varen er på lager, leveringstid ca. 5-8 virkedager

B-varer Plasma Cutter - 90 A - 400 V - Pilot Ignition

  • for cutting metals such as steel, stainless steel, copper, aluminium, etc.
  • IGBT Inverter Technology
  • current can be steplessly regulated
  • powder coated steel sheet casing
  • robust and compact design
  • easy handling
  • delivery package: plasma torch P80, earth terminal, electrode, nozzle, gas pipe
  • high voltage plug not included

Rabatt: 20%

You need a precise, compact and powerful plasma cutter? One that can be used for industry, craft trades and hobby workshops? The S-CUTTER 90 by Stamos Germany has a maximum cutting strength of 25 mm. A light arc takes over the cutting and separating. This arc is started with a high frequency ignition and develops under high electrical voltage between electrode and base material. To increase intensity and stability, additional pressurised air is added. The S-CUTTER 90’s welding current can be steplessly and exactly regulated between 20 and 90 ampere. Thus the device can be ideally adjusted to your needs. The robust and compact construction and the weight of only 34 kg make the plasma cutter easy to transport and enable varied possibilities for use.

Model
S-CUTTER 90
Condition
Factory second
Rated Input Voltage
400 V, 3-Phase(s)
Input Frequency
50/60 Hz
Rated Input Current
14,7 A
max. Input Current
19,1 A
Rated Input Power
9,5 kVA
max. Input Power
12,6 kVA
No-load Voltage
233 V
Cutting Current
20 - 90 A
Duty Cycle
60 %
Cutting Current at 100% Duty Cycle
69,7 A
Cutting Current at 60% Duty Cycle
90 A
Ignition
HF – High Frequency
Cutting Strength
1 - 25 mm
Cutting Width
1,2 mm
Air Flow
240 l/min
Air Pressure
4,5 bar
Length Cable Package
5 m
Length Earth Cable
3 m
Length Power Cable
2 m
Device Cooling
Aeration
Torch Cooling
Air
Power Factor
0,93
Efficiency (under Rated Power)
≥ 0,85
Insulation Class
F
Protection Class
IP21
Measurements (LxWxH)
54 x 28 x 46 cm
Weight
26 kg
Shipping Measurements (LxWxH)
68 x 46 x 52 cm
Shipping Weight
36,2 kg
 
IGBT

IGBT = insulated-gate bipolar transistor. IGBT is a bipolar transistor with an insulated gate electrode. This semi-conducting device is being increasingly used in power electronics because it combines the advantages of two transistor types: the easy controls of the field effect transistor and the fast switching and high breakdown voltage of the bipolar transistor. The IGBT also offers some robustness against short circuits because it limits the electrical continuity. IGBTs are a further development of MOSFET technology.

 
VENTILATORS

Powerful fans ensure an optimal removal of heat from the unit.

 
GAS/AIR CONNECTION

For plasma cutting, a gas is required with which the molten metal is blown away from the work surface. Compressed air is a common solution for this. For this purpose, the plasma cutter has a compressor connection.

 
EARTHING SYSTEM

On the back of every welding machine is a screw with an earthing mark. Before use, earth the unit via a cross-section cable, which must be at least 6 mm².

 
GROUND TERMINAL CONNECTOR
 
CUTTING TORCH CONNECTION
 
SUPPLY VOLTAGE

This device works with a 3-phase connection (400 V +/- 10 %).

 
WELDING CURRENT
 
2-STROKE

Start the weld by placing pressure on the torch button. Stop the process by releasing the button.

 
PLASMA CUTTING

The plasma arc melts the metal and the kinetic energy of the compressed air blows the metal aside.

 
POWER SWITCH
 
DISPLAY

Shows the welding / cutting parameters.

 
OVERLOAD / FAULT LED

The LED light indicates overheating or a malfunction.

 
LOSS OF PHASE LED

The LED lights to indicate that the network connection of the phase has failed.

 
PRESSURE GAUGE (MANOMETER)

Shows the value of compressed air the compressor delivers to the plasma cutter. The plasma cutter has a pressure reducing valve which regulates the air pressure.

The following accessories can be used for the Plasma Cutter S-CUTTER 90 by Stamos Power:

Art. No.
Article
2124
Plasma Spare Parts Set - CUT 85 125 - H / CNC
  • S-CUTTER 90
  • ground cable with clamp
  • hose package
  • accessories (see pictures)
  • instruction manual