B-varer Plasma Cutter - 50 A - 230 V
3428,00 NOK

B-varer Plasma Cutter - 50 A - 230 V

Leverandør: Stamos Power ² | Artikkelnummer EX20020153 | Modell: S-CUTTER 50.1

Statt: 4285,00 NOK Du sparer 857,00 NOK 3428,00 NOK
eller

156,97 NOK /måned

Lær mer

Inkl. mva, avgifter og fraktkostnader*

B-varer

Våre B-varer er stort sett returnerte varer eller produkter som er blitt brukt til utstilling. Det kan forekomme mindre bruksmerker eller små riper. Alt blir testet før det blir lagt ut for salg igjen. Retur- og reklamasjonsretten gjelder som normalt.

Produkt-highlights

  • Plasma
  • Power
  • 230 V
  • Cutting current: 10 - 50 A
  • Cutting thickness: 12 mm
Model
S-CUTTER 50.1
Condition
Factory second
Rated input voltage
230 V, 1-Phase
Input frequency
50 Hz
Input current
22,2 A
Input current max.
28,6 A
Power input
4,8 kVA
Input power max.
6,6 kVA
Open circuit voltage
244 V
Cutting current
10 - 50 A
Duty Cycle
60 %
Cutting current at 100% DC
38,7 A
Cutting current at 60% DC
50 A
Post-gas
~20 s
Ignition
Contact ignition
Cutting capacity
12 mm
Cutting width
2.0-3.0 mm
Air flow
160 l/min
Air pressure
3,5 bar
Length of hose pack
4,85 m
Length of ground cable
3 m
Length power cable connection
2,1 m
Cooling device
Fan
Torch cooler
Air
Power factor
0.73
Efficiency (under rated power)
≥80
Insulation class
F
Protection class
IP21
Dimensions (LxWxH)
43 x 16,5 x 31,5 cm
Weight
9,4 kg
Shipping dimensions (LxWxH)
55,5 x 27 x 42 cm
Shipping weight
15 kg
Teknisk tegning
Leveranseomfang
  • Plasma cutter S-CUTTER 50.1
  • Plasma torch 4,85 m
  • Gas hose 3 m
  • Ground cable with terminal 3 m
  • Plasma electrode - 1 pc
  • Clamping ring - 2 pcs
  • Instruction manual
 
MOSFET

The welder is equipped with a MOSFET transistor. This technology represents the highest standards of performance combined with compact and lightweight design. The result is 93% efficiency! The welding current is very stable and thus ensures a perfect weld.

Se merVis færre
 
VENTILATORS

Powerful fans ensure an optimal removal of heat from the unit.

 
GAS/AIR CONNECTION

For plasma cutting, a gas is required with which the molten metal is blown away from the work surface. Compressed air is a common solution for this. For this purpose, the plasma cutter has a compressor connection.

Se merVis færre
 
EARTHING SYSTEM

On the back of every welding machine is a screw with an earthing mark. Before use, earth the unit via a cross-section cable, which must be at least 6 mm².

 
GROUND TERMINAL CONNECTOR
 
CUTTING TORCH CONNECTION
 
SUPPLY VOLTAGE

This device works with a 1-phase connection (230 V +/- 10 %).

 
GAS POST-FLOW TIME

The time after the weld is finished in which gas continues to flow from the torch; this cools the burner and protects the weld from oxidation.

 
2-STROKE

Start the weld by placing pressure on the torch button. Stop the process by releasing the button.

 
4-STROKE

By pressing the torch button the solenoid valve opens. allowing the gas to flow in. The gas pre-flow ignites the arc at the pre-set current. Releasing the burner button initiates a rise in the current to that of the pre-set welding current. The welding process stops once you press the burner button again.

Se merVis færre
 
PLASMA CUTTING

The plasma arc melts the metal and the kinetic energy of the compressed air blows the metal aside.

 
POWER SWITCH
 
"2T / 4T" SELECTION SWITCH

Choose between the 2T and 4T mode.

 
DISPLAY

Shows the welding / cutting parameters.

 
OVERLOAD / FAULT LED

The LED light indicates overheating or a malfunction.

 
PRESSURE GAUGE (MANOMETER)

Shows the value of compressed air the compressor delivers to the plasma cutter. The plasma cutter has a pressure reducing valve which regulates the air pressure.

Vær den første til å skrive en produktanmeldelse



Gi anmeldelse
Anmeldelser kommer etter en godkjennelsesprosedyre på hjemmesiden

Die mit einem * markierten Felder sind Pflichtfelder.

Gesamtansicht von Plasma Ersatzteilset - CUT 40 50 - klein
749,00 NOK
Inkl. mva, avgifter og fraktkostnader
Schweißhelm – Blaster – ADVANCED SERIES - 2982 - 1
1049,00 NOK
Inkl. mva, avgifter og fraktkostnader
Dette produktet
  • Plasma
  • Power
  • 230 V
  • Cutting current: 10 - 50 A
  • Cutting thickness: 12 mm

Varen er på lager, leveringstid ca. 5-8 virkedager

B-varer Plasma Cutter - 50 A - 230 V

B-varer Plasma Cutter - 50 A - 230 V

Statt: 4285,00 NOK 3428,00 NOK

Varen er på lager, leveringstid ca. 5-8 virkedager

  • Plasma
  • Power
  • 230 V
  • Cutting current: 10 - 50 A
  • Cutting thickness: 12 mm
  • Plasma
  • BASIC
  • 230 V
  • cutting current: 20 - 50 A
  • cutting thickness: 0 - 14 mm

Varen er på lager, leveringstid ca. 5-8 virkedager

Plasma Cutter - 50 A - 230 V - Basic

Plasma Cutter - 50 A - 230 V - Basic

(1)
4349,00 NOK

Varen er på lager, leveringstid ca. 5-8 virkedager

  • Plasma
  • BASIC
  • 230 V
  • cutting current: 20 - 50 A
  • cutting thickness: 0 - 14 mm
  • Plasma
  • Power
  • 400 V
  • Cutting current: 10 - 70 A
  • Cutting thickness: 20 mm

Varen er på lager, leveringstid ca. 5-8 virkedager

Plasma Cutter - 70 A - 400 V

Plasma Cutter - 70 A - 400 V

(1)
6035,00 NOK

Varen er på lager, leveringstid ca. 5-8 virkedager

  • Plasma
  • Power
  • 400 V
  • Cutting current: 10 - 70 A
  • Cutting thickness: 20 mm